Go/no-go: Difference between revisions

Revision as of 21:33, 2 March 2016

Latest revision as of 11:26, 20 June 2025

(42 intermediate revisions by 35 users not shown)

Line 1:

In{{Short general '''go/no go''' testing refers to adescription|A pass/fail test (or check) principle using two boundary conditions or a [[binary classification]].}}

{{original research|date=December 2012}}

In general '''go/no go''' testing refers to a pass/fail test (or check) principle using two boundary conditions or a [[binary classification]].

The test is passed only when the ''Go'' condition is met and also the ''No go'' condition fails.

A '''go/no-go''' test is a two-step verification process that uses two boundary conditions, or a [[binary classification]]. The test is passed only when the ''go'' condition has been met and also the ''no-go'' condition has failed.

The test gives no information as to the degree of conformance to, or deviation from the boundary conditions.

The test gives no information as to the degree of conformance to, or deviation from the boundary conditions. These tests can be used for [[statistical process control]] purposes. There are specific SPC tools that use parameter based measurements (e.g., P-charts) for determining the stability of a process.

It has uses in engineering, psychology, military, and manufacturing. For example, a rocket [[launch status check]] involves a go/no-go test.

== Uses ==

=== Engineering ===

In [[engineering]] the test is traditionally used only to check noncritical parameters where the manufacturing process is believed to be stable and well controlled, and the [[tolerance (engineering)|tolerance]]s are wide compared to the [[frequency distribution|distribution]] of the parameter.

For example, the preceding checks[[launch status check]]s before a [[spaceSpace shuttleShuttle]] liftoff havehad the [[flight controller]] performingperform a go/no -go check on each of the vehicle's critical systems..

=== Psychology ===

In [[psychology]], Gogo/Nono-go teststest, aredeveloped by [[neuropsychologist]] [[Alexander Luria]] in 1940-50s is used to measure a participant's capacity for switching between several types of behavioural response ("plasticity") and control of adequacy of response (impulse control and sustained attention). Since the work of [[attentionAlexander Luria]] andin [[neuropsychology]], such response controlis linked to the cortical [[frontal lobes]].

For example, a go/no-go test that requires a participant to perform an action given certain stimuli (e.g., press a button - '''Go''') and also inhibit that action under a different set of stimuli (e.g., not press that same button - '''No-Go''').

=== Military ===

In the [[United States Army]], drills and proficiency evaluation rubrics are based on a GOgo/NO GOno-go (pass/fail) system. Evaluations involving numerical scores (such as the Physical[[physical Fitnessfitness Testtest]]) convert raw scores to GOgo/NO GOno-go based on cutoffs defined by the particular performance standard for that area. Within a given skills unit, the rubric often specifies GOgo/NO GOno-go scoring for each individual item or concept a soldier is expected to be trained and evaluated on. Usually, a soldier must score GO"go" (i.e. perform satisfactorily) on all sections of an evaluation in order to advance to the next phase of training, to pass the course, and/or to attain the particular qualification.

== Go/no go gauges ==

=== Manufacturing <span class="anchor" id="Go/no-go gauges"></span> <span class="anchor" id="Go/no go gauges"></span> ===

{{main|Go/no-NoGogo gauge}}

Go/no go gauges are encountered in all types of manufacturing.<ref>http://books.google.com/books?id=iD5IAAAAIAAJ&pg=PA78</ref>

[[File:Go & No-Go gauge.jpg|thumb|Go and no-go gauges]]

They may measure a physical dimension, e.g. (50 ±0.01mm), or a value such as the value of a [[Resistor#Preferred values|resistor]] (100Ω ([[Ohm (unit)|ohms]]) ±1%).

Go/no-go gauges are encountered in all types of manufacturing.<ref>{{cite book | url=https://archive.org/details/in.ernet.dli.2015.212228 | page=[https://archive.org/details/in.ernet.dli.2015.212228/page/n101 78] | title=Machine Tool Operation| publisher=McGraw-Hill book Company, Incorporated | last1=Burghardt| first1=Henry D.| year=1919}}</ref>

They may measure a physical dimension, e.g. (50 ±&nbsp;0.01mm01&nbsp;mm), or a value such as the value of a [[Resistor#Preferred values|resistor]] (100Ω100&nbsp;Ω ([[Ohm (unit)|ohms]]) ±&nbsp;1%).

A typical example is a [[plug gauge]].<ref>{{cite book|last=Hoffman|first=Edward G.|title=Fundamentals of Tool Design|year=1985|publisher=Society of Manufacturing Engineers (SME) Publications/Marketing Division|___location=Dearborn|isbn=0-87263-134-6|pages=499–502}}</ref>

A typical gauge used when making [[tennis ball]]s would have two holes, one slightly larger than the other. A manufactured object passes the go/no go test if it goes through the large hole but does not go through the smaller hole; the object fails if it passes through the smaller hole, or does not pass through the large hole.

==See also==

*[[Shock detector]]

*[[Gauge block]]

*[[Qualitative property]]

*[[Shock detector]]

*[[Litmus test (politics)]]

*[[Evaluation of binary classifiers]]

*[[Confusion matrix]]

==References==

<references />

==External links==

== External links ==

* [https://tstbl.co/891-623 An online version of go/no-go test]

{{DEFAULTSORT:Go No Go}}

[[Category:Quality control]]