Ohmmeter: Difference between revisions

Revision as of 18:41, 15 April 2007

Latest revision as of 12:39, 14 June 2025

(225 intermediate revisions by more than 100 users not shown)

Line 1:

{{short description|Tool for measuring electrical resistance}}

An '''Ohmmeter''' is an [[electricity|electrical]] [[measuring instrument]] that measures [[electrical resistance]], the opposition to the flow of an electric [[current (electricity)|current]]. Micro Ohmmeters make low resistance measurements. Megohmmeters measure large values of resistance.

{{distinguish|ohm metre}}

{{Multiple issues|

{{More citations needed|date=November 2012}}

{{lead too short|date=August 2019}}

}}

[[file:Ohmmeter.jpg|thumb|An analog ohmmeter]]

The original design of an ohmmeter provided a small battery to apply a [[voltage]] to a resistance. It used a [[galvanometer]] to measure the electric [[current (electricity)|current]] through the resistance. The scale of the galvanometer was marked in ohms, because the fixed voltage from the battery assured that as resistance decreased, the current through the meter would increase.

An '''ohmmeter''' is an [[electricity|electrical]] [[measuring instrument|instrument]] that measures [[electrical resistance]] (the opposition offered by a circuit or component to the flow of [[electric current]]). Multi-meters also function as ohmmeters when in resistance-measuring mode. An ohmmeter applies current to the circuit or component whose resistance is to be measured. It then measures the resulting voltage and calculates the resistance using [[Ohm’s law]] .

A more accurate type of ohmmeter has an electronic circuit that passes a constant current I through the resistance, and another circuit that measures the voltage V across the resistance. According to the following equation, derived from [[Ohm's Law]], the value of the resistance R is given by:

: <math> R = \frac{V}{I} =IR</math>

An ohmmeter should not be connected to a circuit or component that is carrying a current or is connected to a power source. Power should be disconnected before connecting the ohmmeter. Ohmmeters can be either connected in series or parallel based on requirements (whether resistance being measured is part of circuit or is a shunt resistance).

For high-precision measurements the above types of meter are inadequate. This is because the meter's reading is the sum of the resistance of the measuring leads, the contact resistances and the resistance being measured. To reduce this effect, a precision ohmmeter has four terminals, called Kelvin contacts. Two terminals carry the current from the meter, while the other two allow the meter to measure the voltage across the resistor. With this type of meter, any current drop due to the resistance of the first pair of leads and their contact resistances is ignored by the meter. This [[Four-terminal sensing|four terminal measurement]] technique is called Kelvin sensing, after [[William Thomson, 1st Baron Kelvin|William Thomson, Lord Kelvin]], who invented the Kelvin bridge in 1861 to measure very low resistances.

==Design See also evolution==

The first ohmmeters were based on a type of meter movement known as a 'ratiometer'.<ref>[http://www.g1jbg.co.uk/pdf/MeggerBK.pdf g1jbg.co.uk] {{Webarchive |url=https://web.archive.org/web/20120315011216/http://www.g1jbg.co.uk/pdf/MeggerBK.pdf |date=2012-03-15 }} A pocket book on the use of Megger insulation and continuity testers.</ref><ref>[https://web.archive.org/web/20210225031037/http://www.prolexdesign.com/images/evohmmeter.jpg prolexdesign.com] Illustration of type. Note the absence of any zero adjustment and the changed scale direction between ranges. {{dead link|date=November 2013}}</ref> These were similar to the [[galvanometer]] type movement encountered in later instruments, but instead of hairsprings to supply a restoring force they used conducting 'ligaments'. These provided no net rotational force to the movement. Also, the movement was wound with two coils. One was connected via a series resistor to the battery supply. The second was connected to the same battery supply via a second resistor and the resistor under test. The indication on the meter was proportional to the ratio of the currents through the two coils (hence 'ratiometer'). This ratio was determined by the magnitude of the resistor under test. The advantages of this arrangement were twofold. First, the indication of the resistance was completely independent of the battery voltage (as long as it actually produced some voltage) and no zero adjustment was required. Second, although the resistance scale was non linear, the scale remained correct over the full deflection range. By interchanging the two coils a second range could be provided. This scale was reversed compared to the first. A feature of this type of instrument was that it would continue to indicate a random resistance value once the test leads were disconnected (the action of which disconnected the battery from the movement). Ohmmeters of this type only ever measured resistance as they could not easily be incorporated into a [[multimeter]] design. Insulation testers that relied on a hand cranked generator operated on the same principle. This ensured that the indication was wholly independent of the voltage actually produced.

*[[Ammeter]]

*[[Voltmeter]]

*[[Multimeter]]

*[[Meter (electronics)]]

*[[Measuring instrument]]

Subsequent designs of ohmmeter provided a small battery to apply a [[voltage]] to a resistance via a galvanometer to measure the current through the resistance (battery, galvanometer and resistance all connected in [[Series and parallel circuits|series]]). The scale of the galvanometer was marked in ohms, because the fixed voltage from the battery assured that as resistance is increased, the current through the meter (and hence deflection) would decrease. Ohmmeters form circuits by themselves, therefore they cannot be used within an assembled circuit. This design is much simpler and cheaper than the former design, and was simple to integrate into a multimeter design and consequently was by far the most common form of analogue ohmmeter. This type of ohmmeter suffers from two inherent disadvantages. First, the meter needs to be zeroed by shorting the measurement points together and performing an adjustment for zero ohms indication prior to each measurement. This is because as the battery voltage decreases with age, the series resistance in the meter needs to be reduced to maintain the zero indication at full deflection. Second, and consequent on the first, the actual deflection for any given resistor under test changes as the internal resistance is altered. It is correct only at zero and full scale deflection (infinite and zero resistance respectively) but all other indications will vary with battery voltage, and consequently the value of the adjustable series resistor. The reading for a given resistance under test will become increasingly lower as the battery ages.

*[[Electronic test equipment]]

*[[Electronics]]

*[[Electric circuit]]

*[[List of electronics topics]]

A more accurate type of ohmmeter has an electronic circuit that passes a constant current (I) through the resistance, and another circuit that measures the voltage (V) across the resistance. These measurements are then digitized with an [[Analog-to-digital converter|analog digital converter (adc)]] after which a [[microcontroller]] or [[microprocessor]] make the division of the current and voltage according to [[Ohm's law]] and then decode these to a display to offer the user a reading of the resistance value they're measuring at that instant. Since these types of meters already measure current, voltage and resistance all at once, these types of circuits are often used in [[digital multimeter]]s.

*[[Series and parallel circuits]]

==Precision ohmmeters==

*[[Galvanometer]]

For high-precision measurements of very small resistances, the above types of meter are inadequate. This is partly because the change in deflection itself is small when the resistance measured is too small in proportion to the intrinsic resistance of the ohmmeter (which can be dealt with through [[current divider|current division]]), but mostly because the meter's reading is the sum of the resistance of the measuring leads, the contact resistances and the resistance being measured. To reduce this effect, a precision ohmmeter has four terminals, called Kelvin contacts. Two terminals carry the current from and to the meter, while the other two allow the meter to measure the voltage across the resistor. In this arrangement, the power source is connected in series with the resistance to be measured through the external pair of terminals, while the second pair connects in parallel with the galvanometer which measures the voltage drop. With this type of meter, any currentvoltage drop due to the resistance of the first pair of leads and their contact resistances is ignored by the meter. This [[Four-terminal sensing|four terminal measurement]] technique is called Kelvin sensing, after [[William Thomson, 1st Baron Kelvin|William Thomson, Lord Kelvin]], who invented the [[Kelvin bridge]] in 1861 to measure very low resistances. The Four-terminal sensing method can also be utilized to conduct accurate measurements of low resistances.

*[[Wheatstone bridge]]

==References==

*[[E-meter]], a specialized ohmmeter used by the [[Church of Scientology]]

{{Reflist}}https://www.codrey.com/electrical/ohmmeter-working-and-types/

==External links==

[[Category:Electronic test equipment]]

{{Commons category|Ohmmeters}}

* [http://www.ibiblio.org/kuphaldt/electricCircuits/DC/DC_8.html ''DC Metering Circuits''] chapter from [http://www.ibiblio.org/kuphaldt/electricCircuits/DC/index.html ''Lessons In Electric Circuits Vol 1 DC''] free ebook and [http://www.ibiblio.org/kuphaldt/electricCircuits/ ''Lessons In Electric Circuits''] series.

{{Electrical and electronic measuring equipment}}

[[bg:Омметър]]

[[ca:Òhmmetre]]

[[Category:Electrical resistance and conductance]]

[[da:Ohmmeter]]

[[Category:Electrical meters]]

[[de:Widerstandsmessgerät]]

*[[Category:Electronic test equipment]]

[[el:Ωμόμετρο]]

[[Category:Impedance measurements]]

[[es:Óhmetro]]

[[fa:اهم‌متر]]

[[fr:Ohmmètre]]

[[he:אוהם-מטר]]

[[nl:Ohmmeter]]

[[pl:Omomierz]]

[[pt:Ohmímetro]]

[[ru:Омметр]]

[[sv:Ohmmeter]]