Gyroscopic exercise tool: Difference between revisions

Revision as of 09:21, 13 January 2023

Revision as of 04:45, 16 January 2023

Line 4:

[[File:Video of a complete use session with a gyroscopic exercise tool.webm|thumb|Video showing the use - from starting the rotation with a 'shoestring' over various movements with the holding hand until stopping the rotor with the second hand. The demonstrated speeds are in part very high and not recommended for normal exercise due to the high resulting forces.]]

A '''gyroscopic exercise tool''' is a device used to exercise the [[wrist]] as part of [[physical therapy]] in order to build palm, forearm, and finger strength. It can also be used as a unique demonstration of some aspects of [[dynamics (physics)|rotational dynamics]]. The device consists of a [[tennis ball]]-sized plastic or metal shell around a free-spinning mass, which is started with a short rip string. Once the [[gyroscope]] inside is going fast enough, the person holding the device can accelerate the spinning mass to high rotation rates by moving the wrist in a circular motion.

== History ==

Line 11:

==Mechanics==

{{Tone|section|date=June 2011}}

The device consists of a spinning mass inside an outer shell. The shell almost wholly covers the mass inside, with only a small round opening allowing the gyroscope to be manually started. The spinning mass is fixed to a thin metal [[axle]], each end trapped in a circular, equatorial groove in the outer shell. A lightweight ring with two notches for the axle ends rests in the groove. This ring can slip in the groove; it centrescenters the spinning gyroscope in the shell, preventing the two from coming into contact (which would slow the gyro down) while still allowing the orientation of the axle to change.

Since the spinning mass is balanced, the only possibility to speed up the rotation is for the sides of the groove to exert forces on the ends of the axle. Furthermore, the normal and axial forces will have no effect, so tangential force must be provided by [[friction]]. If the axle is stationary, the friction will only act to slow down the rotation, but the situation is very different if the axle is turned by applying a [[torque]].

Line 17:

This can be accomplished by tilting the shell in any direction except in the plane of the groove or around an axis aligned with the axle. The tilting results in a shift of the axle ends along the groove. The direction and speed of the shift can be found from the formula for the [[precession]] of a gyroscope: the applied torque is equal to the [[cross product]] of the [[angular velocity]] of precession and the [[angular momentum]] of the spinning mass. It is observed here that the direction is such that if the torque is large enough, the friction between the axle and the groove surface will speed up the rotation.

Usually, if the axle were shifting in a horizontal groove, the friction on one end that speeds up the rotation would be cancelledcanceled by the friction at the other end, operating in the opposite direction. But, here, the difference is that a torque is being applied, so one end of the axle is pushed against one side of the groove, while the other is pushed against the other. It does not matter in which direction the torque is applied. If the torque is reversed, each end of the axle will be pressed against the opposite side of the groove, but the direction of precession will also be reversed. The only restriction is that the relative speed of the surface of the axle and the side of the groove due to precession, <math>\mathit{\Omega}_{\mathrm{P}} R_{\mathrm{groove}}</math>, must exceed the relative speed due to the rotation of the spinning mass, <math>\omega r_{\mathrm{axle}}</math>. The minimum torque required to meet this condition is <math> I \omega^2 \left( r_{\mathrm{axle}} / R_{\mathrm{groove}} \right) </math>, where '''I''' is the [[moment of inertia]] of the spinning mass, and '''ω''' is its angular velocity.

Since the acceleration of the rotation will occur regardless of the direction of the applied torque, as long as it is large enough, the device will function without any fine-tuning of the driving motion. The tilting of the shell does not have to have a particular phase relationship with the precession or even to have the same frequency. Since sliding (kinetic) friction is usually nearly as strong as static (sticking) friction, it is not necessary to apply precisely the value of torque (which will result in the axle rolling without slipping along the side of the groove). These factors allow beginners to learn to speed up the rotation after only a few minutes of practice.