C-Bus (protocol): Difference between revisions

Revision as of 23:26, 13 August 2023

Revision as of 08:03, 16 January 2024

Line 3:

{{more citations needed|date=September 2013}}

'''C-Bus''' is a communications protocol based on a seven -layer [[OSI model]] for home and building automation that can handle cable lengths up to 1000 metres using [[Cat-5]] cable. It is used in Australia, New Zealand, [[Asia]], the [[Middle East]], Russia, United States, [[South Africa]], the UK and, other parts of Europe including [[Greece]] and [[Romania]]. C-Bus was created by [[Clipsal|Clipsal Australia]]'s ''Clipsal Integrated Systems''<ref>{{cite web | url=https://www.clipsal.com/Trade/Products/Integrated-Systems | title=Browse Clipsal's innovative electrical products and solutions &#124; Product Catalogue - Clipsal by Schneider Electric }}</ref> division (now part of [[Schneider Electric]]) for use with its brand of home automation and building [[lighting control]] system. C-Bus has been briefly available in the United States but [[Schneider Electric]] has now discontinued sales in the United States.<ref>{{cite web | url=http://www.schneider-electric.us/sites/us/en/support/faq/faq_main.page?page=content&id=FA241002&viewlocale=en_US&country=US&lang=en&locale=en_US&redirect=true | title=Why can't I purchase Schneider Electric US Lighting Control products any more? &#124; Schneider Electric USA | date=10 August 2012 }}</ref>

C-Bus is used in the control of [[domotics]], or [[home automation]] systems, as well as commercial building lighting control systems.

Line 11:

The C-Bus System can be used to control lighting and other electrical systems and products automatically or via [[remote control]] and can also be interfaced to a home security system, AV products or other electrical items. The C-Bus system is available in a wired version and a [[wireless]] version, with a gateway available to allow messages to be sent between wired and wireless networks.

The wired C-Bus system uses a standard category 5 UTP (Unshielded Twisted Pair) cable as its network communications cable and does not require end -of -line termination. Clipsal manufactures a specific category 5 cable for use within electrical distribution panels. This cable has a pink outer sheath which is rated to ensure adequate electrical isolation between the mains voltages found in distribution panels and the extra low voltage C-Bus. Outside of distribution panels standard category 5 UTP cable can be used.

The category 5 C-Bus network wiring uses a free topology architecture. The maximum length of cable used on a C-Bus network is 1000 metres; however, this is easily extended using C-Bus Network Bridges. Up to 100 units can be installed on a C-Bus network and this can also be extended using Network Bridges.

The maximum number of C-Bus networks in one installation is 255 (note that this limitation does not apply if a C-Bus Ethernet Interface is utilisedused, the system size is then limited to IP Addressing only). The maximum number of networks connected in series to the local network via Network Bridges is seven (i.e. using six network bridges).

Each standard C-Bus unit requires 18mA @ 15-36Vdc to operate, however some C-Bus units require up to 40mA.

Line 23:

Each C-Bus network requires a network burden if there are insufficient C-Bus units on the network. This network burden can be enabled on C-Bus output units through software or a hardware burden can be connected to the network.

Each C-Bus network requires at least one system clock -generating unit for data synchronisationsynchronization.

The isolation between the mainsmain supply circuitry and the 36 V DC C-Bus circuitry is greater than 3.5 kV. This is achieved using double wound transformers and opto isolators. This means the C-Bus wiring, connections and circuitry can be considered Extra Low Voltage.

== Wiring Design of C-Bus Systems ==

Line 36:

[[File:CBus Wiring.gif]]

The power control in a C-Bus system lies in a “Dimmer” or “Relay” which is installed in the DB and replaces the traditional switch used in conventional wiring. This Dimmer (or Relay) has a 120/230 V Line interconnection directly to the ceiling light and a neutral connection back from the ceiling light to the Dimmer. The Dimmer will control the light directly and will receive its commands from another device on the C-Bus network (for example, a wall -mounted light switch/keypad). This wall -mounted light switch would not be connected to any load whatsoever; it would be directly connected with the Dimmer by means ofwith a control/signallingsignaling cable. The Dimmers normally come as 4-, 8- or 12-channel DIN-rail mounted devices.

== C-Bus Interoperability ==

As of 9 December 2008, Clipsal opened its C-Bus protocols to anyone who wants to interact with it programaticallyprogrammatically.<ref>{{Cite web |url=http://training.clipsal.com/downloads/OpenCBus/OpenCBusProtocolDownloads.html |title=Open C-Bus Serial Protocol Documents |access-date=2011-02-27 |archive-date=2018-02-21 |archive-url=https://web.archive.org/web/20180221063055/http://training.clipsal.com/downloads/OpenCBus/OpenCBusProtocolDownloads.html |url-status=dead }}</ref><ref>{{cite web |url=http://www.cbus-enabled.com/ |title=Home |website=cbus-enabled.com}}</ref>

Using one of Clipsal's C-Bus interface modules (PCI for RS232 or USB and CNI for Ethernet TCP/IP), you can interact with other home automation systems, or with applications on devices like Android, iPad or iPhone.

The C-Bus protocol was developed using the OSI 7 -layer reference model. C-Bus supports a number ofseveral interfaces such as RS232 and TCP/IP and makes these protocols available to third-party companies.

C-Bus interface specifications are available through the [http://www.cbus-enabled.com/what-cbus.htm C-Bus Enabled Program], however it is necessary to agree to a license agreement.