| name | South East Queensland | |||
|---|---|---|---|---|
| border coordinates | ||||
| -25.74 | ||||
| 151.73 | ←↕→ | 153.73 | ||
| -27.74 | ||||
| map center | 26°44′S 152°44′E / 26.74°S 152.73°E | |||
| image | SEQ ___location map.svg
| |||
| ||||
| image1 | 400px-SEQ_location_map.svg.png
| |||
| File:400px-SEQ ___location map.svg.png | ||||
Module:Location map/data/Australia Queensland SEQ is a ___location map definition used to overlay markers and labels on an equirectangular projection map of South East Queensland. The markers are placed by latitude and longitude coordinates on the default map or a similar map image.
Usage
These definitions are used by the following templates when invoked with parameter "Australia Queensland SEQ":
{{Location map|Australia Queensland SEQ |...}}{{Location map many|Australia Queensland SEQ |...}}{{Location map+|Australia Queensland SEQ |...}}{{Location map~|Australia Queensland SEQ |...}}
Map definition
name = South East Queensland- Name used in the default map caption
image = SEQ ___location map.svg- The default map image, without "Image:" or "File:"
image1 = 400px-SEQ_location_map.svg.png- An alternative map image, usually a relief map, which can be displayed via the relief or AlternativeMap parameters
top = -25.74- Latitude at top edge of map, in decimal degrees
bottom = -27.74- Latitude at bottom edge of map, in decimal degrees
left = 151.73- Longitude at left edge of map, in decimal degrees
right = 153.73- Longitude at right edge of map, in decimal degrees
Alternative map
The {{Location map}}, {{Location map many}}, and {{Location map+}} templates have parameters to specify an alternative map image. The map displayed as image1 can be used with the relief or AlternativeMap parameters. Examples may be found below or in the following:
- Template:Location map#Relief parameter
- Template:Location map+/relief
- Template:Location map#AlternativeMap parameter
- Template:Location map+/AlternativeMap
Precision
Longitude: from West to East this map definition covers 2 degrees.
- At an image width of 200 pixels, that is 0.01 degrees per pixel.
- At an image width of 1000 pixels, that is 0.002 degrees per pixel.
Latitude: from North to South this map definition covers 2 degrees.
- At an image height of 200 pixels, that is 0.01 degrees per pixel.
- At an image height of 1000 pixels, that is 0.002 degrees per pixel.
Examples using ___location map templates
Location map, using default map (image)
{{Location map | Australia Queensland SEQ
| width = 200
| lat_deg = -26.6819
| lon_deg = 153.1177
| label = Mooloolaba
}}
Mooloolaba is still too far south in the map. dangnabbit I thought I fixed the coords of the map. Southport seems more accurate, but I think it still may be off. Too far... south, but only slightly??? Actually, Mooloolaba may be fine - I think I was mistaking where it should be with "Noosa Heads" (still sunshine coast LGA)
Location map many
{{Location map many | Australia Queensland SEQ
| width = 200
| caption = Two locations in South East Queensland
| lat1_deg = -26.6819
| lon1_deg = 153.1177
| label1 = Mooloolaba
| lat2_deg = -27.9736
| lon2_deg = 153.4047
| label2 = Southport
}}
something is wrong, the whole map doesn't show up
Location map+
{{Location map+ | Australia Queensland SEQ
| width = 200
| caption = Two locations in South East Queensland
| places =
{{Location map~ | Australia Queensland SEQ
| lat_deg = -26.6819
| lon_deg = 153.1177
| label = Mooloolaba
}}
{{Location map~ | Australia Queensland SEQ
| lat_deg = -27.9736
| lon_deg = 153.4047
| label = Southport
}}
}}
See also
Location map templates
- Template:Location map, to display one mark and label using latitude and longitude
- Template:Location map many, to display up to nine marks and labels
- Template:Location map+, to display an unlimited number of marks and labels
Creating new map definitions
[[Category:]]